ESP180ESP180User Manual
10 Setup2.4 Installation and removal of ribbon cartridgeThe ESP180 isshipped withoutthe ribboncartridgeinstalled. Pleaseuse thefollowinginstructions t
112.5 ESP180 installationYou have your choice of mounting the ESP180 on a wall orplacing it on a smooth, dry surface. If you install it on a table top
12 SetupThis end acts asthe Edit Button.Press to change thecurrent setting.This end acts as theAccept/Advance Button.Press to accept the current setti
13The message TIME will flash,then the current time will appear.The minutes will flash, and theseconds will be displayed at theleft. The seconds will
14 SetupYou should continue to press the Edit Button until the desiredtime in minutes appears. Then press the Accept/Advance Buttonto accept the displ
15Next, you will see YEAR flashing, and the current year willappear. As before, press the Edit Button until the desired numberappears. Then press the
16 SetupThe preset printing combinations are:NONEPR01 Month Date 12MNDEC12PM1:45PR02 Month Date 24MN DEC12 13:45PR03 Month Date 24HU DEC12 13.75PR04 D
173.1 Setting the sequence in which order Date, Time, Numberand Comment printYou will see DATE flashing; the current date format will appear.To cycle
18NOTE: With the ESP180 you will be able to print up to 21characters. The size of the typeface, however, will depend on thenumber of characters you se
193.3 Setting the time formatNext you will see TIME flashing, then the current time printingformat will appear.To cycle through the availableoptions,
2Thank you for purchasing Acroprint's ESP180 Electronic TimeRecorder. Acroprint offers a complete line of time recordingequipment, accessories, a
20Once you have selected the comment you want, press the Accept/Advance Button to accept it. You will then automatically advanceto the next programmin
21To continue, press the Accept/Advance Button.NOTE: If you select a six digit number, then all 6 characters (twosmall and four alphanumeric character
22Then REPT will flash, followed bythe number of times a number willrepeat.You can program a 1- to 6-digitnumber to repeat up to 9 times. Ifyou want t
23Sunday in October, the days on which Daylight Savings Timebegins and ends. If your business requires other date changingadjustments than these, you
24When you reach the month you need, press the Accept/AdvanceButton to accept the month shown on the display.Then the date will appear on the display,
254. Error messagesERR: When this appears, it indicates there is no printheadmovement. There are three probable causes:- The printhead may have jammed
26NOTE: The Reset ButtonYou can find the ESP180 Reset Button on the back of the unit,behind the wall mounting bracket. If you press this button, it wi
275. Manufacturer's warrantyManufacturer's warrantyShould you have any questions concerning your warrantyinformation or supplies, please con
5640 Departure DriveRaleigh, NC 27616IN USA 800.334.7190www.acroprint.comP/N 06-0251-000 Rev. B
3Table of Contents1. Introduction ...41.1 Product overview ...
41. Introduction1.1 Product overviewThe Acroprint Electronic Side Printer model 180 (ESP180) hasbeen designed to be a versatile, reliable, inexpensive
5Introduction1.2 General specificationsPower supply: voltage input 120VAC, 50/60 Hzoutput 16VAC @ 1.5ADimensions: 5 in. wide x 7.15 in. tall x 6.5 in.
62.1 Site requirements/safety instructionsThe ESP180 can be installed in any normal office environment.No special wiring or cooling is required. Howev
7Setup2.2 Unpacking and inspectionOpen the shipping carton and carefully remove the contents:• ESP180 • 1 key• Power cable • Ribbon• User Manual • 3 s
8 Setup2.3 Connecting powerBefore you place the ESP180 on a wall or a flatsurface, you must make sure the power is connected.Before connecting the pow
9SetupThe power cable is then inserted intothe recessed area on the bottom ofthe clock. Push the cable into theopening, being careful to hold thecable
Comments to this Manuals